2011 Tacoma Backup Camera Wiring Diagram

By | July 10, 2018



Install a Backup Camera in your 2011 Tacoma with the Right Wiring Diagram



As vehicle safety technology advances, rear-view camera systems have become an essential tool for any driver. The new Toyota Tacoma series has been a reliable vehicle since its introduction in 1995 and continues to stand out due to its exceptional performance and build quality. It's no wonder that so many drivers opt for a Tacoma when it comes to a dependable daily driver or weekend off-road machine. In order to get the most out of modern technologies, it’s important to familiarize yourself with backup camera systems and the wiring diagram for your Tacoma.

Installing a backup camera on your 2011 Tacoma is not difficult when you understand the wiring diagram. With some general knowledge of electrical wiring, you should be able to complete the installation process. This article will explain the components of a rear-view system and the wiring diagram for your Tacoma. Additionally, the tips provided here will ensure that you get the most out of your new backup camera system.

Understanding the Components



A rear-view camera system consists of four main components: the camera box, the monitor, the wiring harness, and the power source. The camera box is typically installed above the license plate or below the rear window. Depending on your Tacoma's model, the camera box may be a part of the particular model's bumper design. The monitor can be any type of flat-screen or LCD display but is usually a 7 or 10-inch display. This monitor is connected to the wiring harness to receive power and control signals from the car's computer. Additionally, the power source, like an in-car power inverter or car battery, provides power to the whole system.

Wiring Diagram for Your Tacoma



The wiring diagram for your 2011 Tacoma will help you understand how each of the components are connected in order to operate correctly. The first step is to determine where the power source will be located; the power will be connected from the power source directly to the camera before passing onto the wiring harness and then ultimately to the monitor.

From the camera and power source, the positive and negative wire must lead to the wiring harness. The positive cable should be connected to ‘+’ terminal and the negative cable should be connected to the ‘-’ terminal. Once complete, the wiring harness will connect to the monitor and provide it with power and control signals. If a reversing switch is needed, it will be connected to the wiring harness in order to give the monitor a signal when the car goes into reverse.

Useful Tips for Installing a Backup Cam




  • When connecting the camera, make sure the wires are securely in place and are not damaged.

  • If using the vehicle’s power source, choose the right fuse and don’t overload the system.

  • Test the connection and camera’s image quality before closing up the installation.

  • If you have any problems installing the system, contact a professional installer.



Installing a backup camera in a 2011 Tacoma doesn’t need to be difficult. With a clear understanding of the wiring diagram, a few useful tips, and some basic electrical knowledge, you can get the most out of your new rear-view system. As always, use genuine parts and be sure to check for any recalls that your specific vehicle may be part of before starting.


2nd Gen Tacoma Wiring A Backup Camera With Factory Harness Toyota Over Land

2nd Gen Tacoma Wiring A Backup Camera With Factory Harness Toyota Over Land


2006 Tacoma Reverse Camera Install Yotatech Forums

2006 Tacoma Reverse Camera Install Yotatech Forums


07 Tundra Backup Camera Toyota Forum

07 Tundra Backup Camera Toyota Forum


Backup Camera Wiring Pigtail For 2007 2009 Toyota Tundra 2019 Tacoma Trucks

Backup Camera Wiring Pigtail For 2007 2009 Toyota Tundra 2019 Tacoma Trucks


2012 Reverse Camera Switch Tacoma World

2012 Reverse Camera Switch Tacoma World


2013 Tacoma Oem Backup Camera Install Question World

2013 Tacoma Oem Backup Camera Install Question World


Back Up Camera Install On A Base 2014 Tacoma World

Back Up Camera Install On A Base 2014 Tacoma World


How To Install Toyota Tacoma Rear View Camera Steps Source Backup Cameras

How To Install Toyota Tacoma Rear View Camera Steps Source Backup Cameras


2nd Gen Tacoma Wiring A Backup Camera With Factory Harness Toyota Over Land

2nd Gen Tacoma Wiring A Backup Camera With Factory Harness Toyota Over Land


Car Rear View Camera Reverse Backup For Toyota Corolla Vios 2007 2011 S Reviews Zoodmall

Car Rear View Camera Reverse Backup For Toyota Corolla Vios 2007 2011 S Reviews Zoodmall


Toyota Tacoma Oem Integrated Backup Camera System Systems Car Integrations

Toyota Tacoma Oem Integrated Backup Camera System Systems Car Integrations


Toyota Tacoma 2015 2018 Service Manual Reverse Signal Circuit Rear View Monitor System Park Assist Monitoring

Toyota Tacoma 2015 2018 Service Manual Reverse Signal Circuit Rear View Monitor System Park Assist Monitoring


Wireless Backup Camera Is Safe Economical And Easy To Install

Wireless Backup Camera Is Safe Economical And Easy To Install


Toyota Tundra Backup Camera Replacement Rear View Mirror Monitor

Toyota Tundra Backup Camera Replacement Rear View Mirror Monitor


Curt T Connector Vehicle Wiring Harness With 4 Pole Flat Trailer Custom Fit C55513

Curt T Connector Vehicle Wiring Harness With 4 Pole Flat Trailer Custom Fit C55513


2013 Tacoma Oem Backup Camera Install Question World

2013 Tacoma Oem Backup Camera Install Question World


Hd Touch Screen 9 Inch Android 11 0 Radio Gps Navigation System For 2005 2013 Toyota Tacoma

Hd Touch Screen 9 Inch Android 11 0 Radio Gps Navigation System For 2005 2013 Toyota Tacoma


07 Tundra Pre Wired Backup Camera And Monitor Plug Connection Diagrams Toyota Forum

07 Tundra Pre Wired Backup Camera And Monitor Plug Connection Diagrams Toyota Forum


Guide To Car Stereo Wiring Harnesses

Guide To Car Stereo Wiring Harnesses